5 HP Compressor Duty Electric Motor 1 Phase 3450 RPM 56 Frame 7/8" Shaft 230V

Description

BRAND NEW!!!
5 HP  –  1PH    56HZ   –  3450RPM   –   22 FULL LOAD AMPS AT 230V
WILL REPLACE FRAME SIZES  143T / 145T / 56 / 56H / 56HZ  ( THIS MOTOR WILL REPLACE MULTIPLE BOLT PATTERN CONFIGURATIONS)
3450 RPM  –  22 AMP  –  7/8″ SHAFT  Diameter
ELECTRIC MOTOR FOR BELT DRIVEN AIR COMPRESSORS
Capacitor Start & Capacitor Run Compressor duty motor
Full Manufacturers Warranty + FREE SHIPPING to lower 48 states
Same Day shipping if ordered 3PM EST Mon-Fri
If you need help choosing the right motor to replace your old one. Please view our 5HP technical guide below.
Technical Info:
Horsepower: 5HP.
Voltage:  230V
( Motor NOT rated for any voltage less than 208 VAC)
Amperage: 22.0 fl amps at 230v
Rotation: CCW   Counter Clockwise Rotation when viewed from the shaft end.
THIS MOTOR IS NOT REVERSIBLE
RPM: 3450
Frequency: 60hz
Shaft Diameter: 7/8″ Keyed shaft
Shaft Length:  2.25″
Efficiency:  80%
Service Factor: 1.0
Enclosure: ODP  Open Drip Proof  THERMALLY PROTECTED WITH MANUAL RESET
Phase: One / Single Phase.  2 pole
5HP
Motor
Technical Guide:
For
all you “Do it Yourselfers out there” its vitally important that you
match up the specs on your old motor, with the new motor you’re
purchasing. All 5HP motors are NOT created equal. A 5HP 56frame motor is
drastically different than a 5HP 184T frame motor. Below is a quick
check list for you to reference when sizing up the right motor for your
application. All of the information you need to know can be found right
on your electric motors nameplate/sticker. usually found on the side of
the motor.
1: Amperage
..   This is your electric motors TRUE power rating. HP ratings have
been made suspect over the years by large retailers who like to use
“peak HP” or ” SPL ” in their terminology. The Motor’s amp rating does
not lie. Please make sure your FL amp (FULL LOAD) rating on the motor
you’re replacing is within 10% of the FL Amp rating of the motor you
intend to buy.
Example 1:
If your current motor says  21 FL
amps at 230VAC. Then you would be safe replacing your motor with a 19FL
amp thru 23 FL amp electric motor 230volt.
Example 2:
If your
current motor says 21 FL amps at 230VAC. Then you replace it with a 15
FL amp motor. That 15A motor is NOT strong enough for the task, and will indefinitely fail.
2: Frame Size
.. The frame not only
constitutes the bolt pattern, it also depicts the overall size and torque. The larger the frame, the stronger the motor. If your current motor
you’re replacing shows 56, 143T or 145T on the nameplate. Its extremely
important that you replace it with that frame size.  Improperly sized
motors will inevitably result in motor failures.
Example:
If
your existing motor says 5HP 184T frame, and you elect to replace it
with a 5HP 56frame.. That would be similar to using a 4 cylinder engine to power a school bus.  This is why its important that your
new motors frame size matches the old motor you’re replacing. This will
ensure your replacement motor will work for years to come.
3: Phase and Voltage
.. If your machine requires a 230volt electric motor on single phase
power. You would want to incorporate a 1-phase 230vac electric motor for
your application. 230V electric motors cannot handle voltages less than 208V. They will run too hot and you will experience motor failure. If your Single phase applicaction requires a 208V or less motor, please contact us and we will set you up with the proper motor.
4: RPM
.. Matching up the RPM is quite
important. The wrong speed can damage your pump.  The RPM does not have
to match exactly, but you do need to be the neighborhood.
Example:
3510rpm, 3550, 3450 are all the same. They all fall under the umbrella of whats known as 3600RPM motors.
5: Shaft Diameter
..  With a tape measure. Measure the outside diameter on your electric
motors shaft. The most common 5HP compressor duty motor shaft diameters
are 5/8″ on 56 frame motors                               7/8″ on 56HZ  /  143T  /  145T frame motors                            1 1/8″ on 182T or 184T frame motors.
By matching up the proper shaft diameter, you will be able to reuse the original motor pulley that came on your machine.
If you have any questions in regards to sizing up the proper motor. Please feel free to contact us.
Terms and Conditions
Payment Information:
VISA / MASTERCARD / AMEX / DISCOVER /  PAYPAL accepted.
Contact Us:
Please
feel free to contact us anytime through the ebay message board.  On
each of our ebay listings you will see options to contact us. The “ask
seller a question” link  and the “Contact seller” link are the two best
ways to contact us. Your question will automatically link to your
purchase or the item in question and will be answered Mon-Fri during our
operating hours.
No ebay question or message goes unanswered.
Please DO NOT contact us via email regarding your ebay purchase.
Return Policy:
Here is how to arrange an ebay return
http://pages.ebay.com/
help/buy/return-item.html
Arrangements must be made within 30 days of purchase.
Returns are permitted only with the prior approval of UPE_Group.
A minimum restocking fee of 15% will be applied on returns due to customer error.
Authorized
returns will be credited at the transaction price, minus any applicable
fees. The adjusted amount will refunded back to the buyer’s payment
method after the item has been returned back to UPE_Group.
The
above fees will NOT be charged on items returned due to manufacturers’
defect or shipping errors caused by UPE_Group, USPS or FEDEX.
Shipping Address:
We ship to the buyers ebay ship to address. Please make sure your ship to address is correct before checking out.
Domestic Shipping:
We are open Monday through Friday shipping eBay orders
.
All orders ship within 24 BUSINESS Hours of payment confirmation
.
We ship most orders the same day that we receive them, just as long as
your payment clears before mid afternoon EST. Items are shipped USPS or
FEDEX ground. The shipping method will be listed on the
shipping/payments tab or underneath the buy-it-now button on all ebay
listings. We generate shipping labels through ebay, so your tracking
info will be emailed to you the moment your shipping label is generated.
You can click the link on your tracking info to get up to date tracking
info regarding your shipment. You can find the link on your transaction
details page, or under the “Buying” portion on your “My eBay” page. For
specific shipping info and combined shipping rules, please click the
“shipping and payment” tab on any of our ebay listings. That link will
show you the shipping specifics and combined shipping rules relating to
that specific item.
International Shipping:
All
items we sell are available for international shipping through the ebay
3rd party Global Shipping program. UPE_Group will ship your item to the
ebay global shipping center in Kentucky. From there, eBay forwards the
package to your international destination.
Please click the shipping/payments tab of our listings for international shipping information or visit this ebay page.
http://pages.ebay.com/
help/buy/shipping-globally.
html
Combined Shipping Rules:
Simply
use the ebay shopping cart feature and add items to your cart for one
flat shipping rate. eBay’s Combined shipping Rules are usually
implemented
by all ebay sellers. The only
way for eBay to recognize multiple items going to the same address is by
using the ebay shopping cart feature. Add items into ONE ebay shopping
cart and check out on ONE transaction/purchase. You can also request an
invoice from the seller once you have added all of the items into your
ebay shopping cart.
Tracking Information:
We
provide Tracking info on every item that is purchased on ebay. The
tracking info will be emailed to you the day your order is shipped.
Feedback Policies:
Anyone
who purchases from us gets positive feedback. If you have any sort of
issue with the item you received from us, please contact us before
leaving a bad feedback. We would be more than happy to correct any
issue. Regardless if we accidentally sent you the wrong item (which
seldom happens)  or the customer ordered the wrong part by mistake. WE
WILL correct any potential problem.
Sales Tax:
The Purchaser shall be responsible for the payment of all state sales taxes.
Liability:
UPE_Group
is a dstributor and as such, has no direct or indirect control over the
materials, processes, or quality control procedures used by the
manufacturers of the products we resell. Accordingly, UPE_Group will NOT
be held responsible for damages resulting from product defects, or,
from mis-applications/improper installations by the customer or end
user. It is the purchasers responsibility to determine the suitability
of the product for the specific application.
If it is deemed defective,
UPE_Group
shall be held harmless of any and all damages including (but not
limited to) physical injury, property damage, water damage or otherwise
for any reason.
If
the purchased item is deemed defective, UPE_Group will make
arrangements to replace the defective item at no additional costs to the
customer.
CA Prop 65  WARNING:
Some
of the products sold by Universal Pneumatic and Electric Group may
contain chemicals known to the State of California, Vermont and others
to cause cancer, birth defects, or other reproductive harm. It is the
purchasers responsiblity to determine the suitability of these products
for your specific application. Including, but not limited to, using
alternative products. UPE_Group shall be held harmless of any and all
damages including but not limited to physical, property, water or
otherwise for any reason. Your use of any information or materials on
this listing is entirely at your own risk, for which we shall not be
liable.
By submitting your order, the purchaser acknoledges agreement with the Terms & Conditions as outlined here and our website.
PLEASE CONTACT US WITH ANY QUESTION YOU HAVE REGARDING ANY OF OUR PRODUCTS OR TERMS AND CONDITIONS.
THANK YOU
UPE_GROUP